Hot Splash Heat Pump 3.75kw Plug and Play for Above Ground Swimming Pools up

Hot Splash Heat Pump 3.75kw Plug and Play for Above Ground Swimming Pools up

Hot Splash Heat Pump 3.75kw Plug and Play for Above Ground Swimming Pools up

Hot Splash Heat Pump 3.75kw Plug and Play for Above Ground Swimming Pools up to 9m3 for Summer Use. Hot Splash Heat Pump - New larger sized model: Hot Splash Heat Pump 3.75kw are now in stock! Hot Splash Heat Pump Description. Introducing the fabulous new improved Hot Splash Heat Pump 3.75kw.

The new Hot Splash has improved heat output, quieter operation and works at lower air temperatures (down to +10c, was +15c). The World's Smallest Plug and Play Heat Pump! This model has a 3-pin UK RCD/Plug. Slash the cost of heating your pool using the Hot Splash rather than an electric heater. They are designed for small above ground pools up to around 9m3 of water. The Hot Splash heat pumps are incredibly easy to setup for your pool. They offer much lower running costs that using an electric pool heater. The New Hot Splash outputs up to 3.75kw of pool heat but only uses 0.56kw of electricity! Hot Splash Heat Pump Features. Improved heat output: Now outputs up to 3.75kw of pool heat from only 0.56kw of electricity used. Dimensions - 29 x 31 x 37cm (l x w x h). Suitable for pools up to 9m3 of pool water. Desired water temperature can be set to be between 20c and 40c. Simple "plug and play" heat pump. Comes complete with 2.5 meter power cable and UK 3-pin Plug / RCD for electrical safety.

Includes 2 meters of 1.25? (32mm) pool hose to connect to your pool. (32mm) water connections for hose.

2 x hose clips included. Operates to lower air temperatures: Now operates with air temperatures of +10c and above.

Requires a flow rate of 2.5m3 an hour from your pump/filter. Eco Friendly R32 refrigerant gas. Full Flow and No Frost technology - No bypass required. Integrated carry handle - makes it easy to lift and move when not in use.

Digital control panel - simply set the pool temperature required and the Hot Splash will tun on and off as required to maintain the desired pool temperature. High quality polymer - corrosion and UV resistant case.

Gives much lower running costs than an electric pool heater. Note: As the Hot Splash requires an air temperature of +10c and above to operate, it is aimed at summer use eg May-Sept. It cannot operate during the day or night when the air temp is below +10c. If you require a model which can work at lower temperatures, please look at the Nano mini heat pump. Hot Splash Heat Pump Easy to Use Digital Control Panel.

The Hot Splash HS40 has a touch screen easy to use display. Simply use the up and down arrow keys to set your desired pool temperature and the Hot Splash will automatically turn on and off to maintain the desired temperature. Hot Splash Heat Pump is fitted with UK Plug/RCD. This listing is for the 3-pin UK RCD/Plug. We can send with a EU 2 pin plug if requested.

Note: The Hot Splash heat pumps require a 220v or 240v, 50hz power supply and therefore are not suitable for use in the USA/Canada (which uses a 110v, 60hz power supply). What size heat pump do I require for my pool? How to Calculate Your pool Water Volume.

You can easily calculate the water volume in your pool as follows. To calculate the volume of a round pool, you can use the formula. Pool Volume = 3.14 x radius x radius x depth. Measure the diameter of the pool in metres. Half the diameter to give the radius of the pool.

Multiply 3.14 x radius x radius x pool depth. A 10ft x 30 pool.

Diameter = 10' x 0.305 = 3.05m. Radius = 3.05 / 2 = 1.52m. Volume = 3.14 x 1.52 x 1.52 x 0.76m = 5.5 m3. The Hot Splash 3.75kw supports pools up to 9m3 so would be OK for this pool.

Pool volume = length x width x depth. 6m x 4m pool, 0.8 m deep = 6 x 4 x 0.8 = 19.2 m3. Maximum for Hot Splash 3.75kw = 9m3 so this pool would be too large - look at our SunSpring heat pumps.

Typical Pool Sizes and Volumes. Intex above Ground pool = 3.6 m3 - Hot Splash OK! Intex above Ground pool = 5.5m3 - Hot Splash OK!

Intex above Ground pool = 9.6 m3 - Hot Splash too small (we would recommend allowing 20% clearance on water volume to heat pump capability volume). If your above ground pool is larger than 9m3, the please look at our SunSpring range of pool heat pumps as these will cover pools that have from 12m3 of water up to 35m3 of water. Please Specifications tab at the top of the page.

Installation is very easy and straightforward. The hot splash is connected to your existing pool pipework. It uses the existing pool circulation pump to pump the pool water through it. Please see the user manual below for more information on how to install your Hot Splash heat pump.

The Hot Splash only uses 0.56kw of electricity to produce 3.75kw of pool heat. If you compare this with an electric pool heater, a 3.75kw electric pool heater would use 3.75kw of electricity. We sell both 1.5? Hot Splash 3.75kw Heat Pump Brochure. Hot Splash 3.75kw Heat Pump User Manual.

For more information, also see our FAQs page. (excludes Scotland and some UK postcodes). Please message us for a quotation to deliver to other countries. HeatPumps4Pools are the leading UK based specialist supplier of heat pumps and related pool products.

Operating from Basildon in Essex in the UK, we are the leading specialist supplier of swimming pool heat pumps to the UK and Europe. We have a wide range of the best swimming pool heat pumps to suit any pool size and type. We are always happy to offer free friendly advice on the best heating solution for your pool.

We are happy to provide free pre and post sales support. Customers are also welcome to visit us in our offices in Basildon Essex.
Hot Splash Heat Pump 3.75kw Plug and Play for Above Ground Swimming Pools up